[. . . ] Quick Start Guide HT-S3505 Supplied Accessories Make sure you have the following accessories: a Indoor FM antenna b AM loop antenna c Remote controller and two batteries (AA/R6) d Speaker Package *1 Configuration of the rubber stoppers may be different from the figure, such as being 2 sheets instead of 1 sheet, but the total number will be same. a b c Please connect 1 , 2 , 3 , 4 , 5 and 6 for 5. 1-channel surround. 2 Front speaker R 3 Center speaker 1 Front speaker L d Front speakers (White) (Red) Speaker cables 3. 0 m Center speaker (Green) Speaker cable 3. 0 m Surround speakers (Blue) (Gray) Speaker cables 8. 0 m Red Green White 20 thin rubber stoppers*1 8 thick rubber stoppers*1 (For Front/Center/ (For Front/ Surround speakers) Surround speakers) Subwoofer (Purple) Speaker cable 4 floor pads 3. 0 m Using the Remote Controller Remote control sensor AV receiver Batteries (AA/R6) Note Approx. [. . . ] All the settings are organized in a user-friendly structure, which covers the whole TV screen area. ■ Opening the Setup menu 1 Home 2 1 2 I npu t Aud i o I nfo L i s t e n i n g Mode AM FM TV CD PORT [ E n t e r : Se l e c t ] Menu 1. HDMI Input Component Digital Audio Sp Config Sp Distance Level Cal Audio Adjust Source Setup Hardware HDMI Setup BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD PORT ■ Navigating through the menus 1 2 4 1 2 3 4 5 Turn on the AV receiver.  Input You can select the input source while viewing the related information.  Audio You can change various audio settings such as tone controls, the subwoofer and center channel levels.  Info You can view various information about the currently selected input source.  Listening Mode You can select the listening modes that are grouped in categories. ■ Closing the menu ■ Navigating through the menus ■ Returning to the main menu ■ Closing the menu Note • This procedure can also be performed on the AV receiver by using SETUP, the cursor buttons, and ENTER. 5 -5- -6- 5. Getting to Know the AV receiver Front Panel a b cd e f gh ij k l m n Remote Controller To control the AV receiver, press RECEIVER to select Receiver mode. a. Sets the AV receiver to On or Standby. i. Displays various information about the currently selected input source. n. Used for the Sleep function. a b i j c d e op q r s f l m k Each input selector button (BD/DVD, GAME, etc. ) selects the input terminal with the same name on the rear panel. Troubleshooting Can't turn on the AV receiver. Make sure that the power cord is properly plugged into the wall outlet. a Sets the AV receiver to On or Standby. c You can use two sets of front speakers with the AV receiver: Speakers A for up to 5. 1-channel playback in your main listening room and Speakers B for 2-channel stereo playback in another room. d The remote control sensor receives signals from the remote controller. [. . . ] To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press 8 ON/STANDBY. “Clear” will appear on the AV receiver's display and the AV receiver will enter standby mode. Note that resetting the AV receiver will delete your radio presets and custom settings. Tel: 072-831-8023 http://www. onkyo. com/ Tel: 800-229-1687, 201-785-2600 http://www. us. onkyo. com/ Tel: +49-8142-4401-0 http://www. eu. onkyo. com/ Tel: +44-(0)1628-473-350 Tel: 852-2429-3118 http://www. onkyochina. com/ Tel: 86-21-52131366 http://www. cn. onkyo. com/ -7- [. . . ]